by Carlyn Maw on January 26, 2014, no comments
The highlight of Friday for me was the day blending into the evening’s festivities. We held the Tech Disruptor Showcase from 6 to… later than we should have. Barb, Jen and I all got to be in the store at the same time, which was awesome. Between the Cause-And-Effect machine going up, printers being taken […]
by Carlyn Maw on January 26, 2014, no comments
Day 18 was way back on January 21st, the same day as Hackaday: The Gathering. It is pretty clear that if I don’t start the blog post immediately after the shift, the post will be lame sauce. However, going to The Gathering was totally worth it. I made a subset of the top-24 images from […]
by Carlyn Maw on January 20, 2014, no comments
TL;DR The Intel Experience Store has extended it’s run from the original date of January 25th until January 30th. I could have lasted until the end of this week with the mess we’ve made, but I couldn’t make it through two. So I cleaned and organized the best I could on Friday, blowing through the […]
by Carlyn Maw on January 15, 2014, 2 comments
TL;DR: Tuesday I was very excited to turn a Dust Buster into a blow gun. Turns out they can’t be modded that way so easily. Something about centrifugal fans. So I made a literal “suction cup” instead. While waiting for the battery to charge I started munching on a Dell laptop. Looking forward to seeing […]
by Carlyn Maw on January 13, 2014, no comments
TL;DR The day ended up having 3 parts in parallel: fixing a solder joint to make a curling iron reusable again, taking the amplifier apart completely, and more BrushBots. Fixing One of our experience agents was about to return her curling iron because it didn’t work any more, but thought it might be more fun […]
by Carlyn Maw on January 11, 2014, one comment
TL;DR: BrushBots/BristleBots are always awesome and Wednesday’s race-themed event was no exception. I didn’t get as many pictures and videos as I would have liked because it was too busy to keep up! Eventually the tracks had to come off the table and more to the floor to make room. We learned that there are […]
by Carlyn Maw on January 7, 2014, no comments
TL;DR Monday was all about going full speed to make a track for the BrushBot Races happening on Wednesday at 12:30 PM to 3:30, 1421 Abbot Kinney Blvd. Intel will be donating money to MakerEd if the event is a success, so come on down and tweet about it. I have 25 kits, or bring […]
by Carlyn Maw on January 3, 2014, no comments
TL:DR I want to lead today’s post with a big giant thank you to GrandadIsAnOldMan and his Bargain Store Project #32 Styrofoam Cup and Plate Hovercraft. In addition to stripping down more objects from the stash, both the hovercraft (success!) and jet car (fail.) were attempted on Thursday. The hover craft was updated with construction paper […]
by Carlyn Maw on December 30, 2013, one comment
Saturday the 21st and Saturday the 28th were hopping with lots of folks joining in on the taking apart of many many objects. I tried to record as much as possible but it was such a wonderful feast of dismantlement it was tough to keep up! Oh, and there was face painting on the 21st. […]
by Carlyn Maw on December 20, 2013, one comment
TL;DR Bunnies! Hopping! Okay a little bit more. Thursday I continued the printer/scanner break down that Jen started, removing the metal assembly from it’s plastic case. One of the printer’s circuit boards yielded up more parts at heat gun point, primary target the connectors for the motors. I set up a “nail board” of sorts […]